- Home
- Show all categories
- Models & Clones
- A1000 Accelerators
- A1200 Accelerators
- A2000 Accelerators
- A3000 Accelerators
- A4000 Accelerators
- A500 Accelerators
- A600 Accelerators
- Bridgeboards & Emulator Cards
- CD32 Accelerators
- CDTV Accelerators
- Custom Chips
- Digtizers & Framegrabbers
- Flickerfixer & Scandoubler
- Floppy Controller
- Genlocks
- Graphics (non RTG) & Video Cards
- Graphics Cards (RTG)
- I/O Karten
- IDE Controller
- ISDN & Modem
- Keyboards & Adapters
- Kickstart Switchers
- MIDI Devices
- Misc ZORRO Cards
- Misc. Hardware
- Monitors
- Network Cards
- Processors
- RAM Expansions
- Scanner
- SCSI Controller
- Sound Cards
- Soundsampler
- Tape Drives & Backup
- Time Base Correctors
- Tower Kits
- Zorro Extenders & Busboards
- Mystery Corner
- Browse by Connection
- Sitemap
Network Cards
Hydra Systems: AmigaNet Zorro II
Connection: Zorro II |
Rev 1.1 card with 2 x BNC and 1 x AUI
Rev 1.1 card with 2 x BNC and 1 x AUI
Rev 1.1 card with 1 x BNC and 1 x AUI
Rev 1.1A card with 1 x BNC and 1 x AUI, Front
Rev 1.2 card with 1 x BNC
Rev 1.1A card with 1 x BNC and 1 x AUI, Back
Hi Res Version, Rev 1.0 - 417K
Hi Res Version, Rev 1.1, 2 x BNC, 1 x AUI - 59K
Hi Res Version, Rev 1.1, 1 x BNC, 1 x AUI - 829K
Hi Res Version, Rev 1.1A, Front - 448K
Hi Res Version, Rev 1.2 - 353K
Hi Res Version, Rev 1.1A, Back - 378K
Closeup of Rev 1.1A card, left side - 579K
Closeup of Rev 1.1A card, right side - 573K
Type: | Ethernet |
10Base2 (BNC & Coax, ThinNet): | Yes |
10Base5 (AUI & Coax, ThickNet): | Yes (Rev V1.1 and earlier boards) |
10BaseT (RJ45 & UTP): | Yes (no for Rev V1.1 boards and earlier, some cards may require the connector upgrade) |
100BaseTX (RJ45 & UTP): | No |
SANA-II Driver: | Yes (hydra.device) |
MNI Driver: | Yes (z2-dp8390.mni) |
Other Driver: | No |
The AmigaNet is a full length Zorro II Ethernet card (NatSemi 32490CN) for the Amiga. Depending on the specific versions of the card, it supports 10Base5, 10Base2 and 10BaseT. To support 10BaseT, your card may require an optional upgrade to attach the RJ45 connector to the board. Earlier revisions of the board have two BNC connectors, rather than the conventional single connector that most ethernet cards have. This means you do not need the "T" connector which you do with other ethernet cards. You simply attach both BNC connectors to the same network segment. The AmigaNet has been reported to transfer at up to 600k/sec. The Zorro II network card released by GVP called the A-Net 2000 was simply this card rebadged.
Jumpers
There is only one set of jumpers, block F1, which has six pairs of pins. When all are in the down position, it is set to ThinNet 10Base2 (CheaperNet). When all are jumpered in the up position, it is set to use the AUI port for 10Base5.
Board Layout
_________________________________________________________________
| |___
| |
| :::::: F1 |
| |# 10Base5
| |# /AUI
| |# Port
| |# (DB15)
| |#
| |_
| |_| BNC
| |_
| |_| BNC
|_________________________________________________________________|
||||||||||||||||||||||||||| |
Contributions to this page by:
Calum Tsang, Mats Magnusson, RiWa & Friends, Takahasi Kasiko, Thomas Weygand, Warren Block
Letzte Änderung des Artikels: 2009-01-26 21:28
Revision: 1.0
You cannot comment on this entry