- Home
- Show all categories
- Models & Clones
- A1000 Accelerators
- A1200 Accelerators
- A2000 Accelerators
- A3000 Accelerators
- A4000 Accelerators
- A500 Accelerators
- A600 Accelerators
- Bridgeboards & Emulator Cards
- CD32 Accelerators
- CDTV Accelerators
- Custom Chips
- Digtizers & Framegrabbers
- Flickerfixer & Scandoubler
- Floppy Controller
- Genlocks
- Graphics (non RTG) & Video Cards
- Graphics Cards (RTG)
- I/O Karten
- IDE Controller
- ISDN & Modem
- Keyboards & Adapters
- Kickstart Switchers
- MIDI Devices
- Misc ZORRO Cards
- Misc. Hardware
- Monitors
- Network Cards
- Processors
- RAM Expansions
- Scanner
- SCSI Controller
- Sound Cards
- Soundsampler
- Tape Drives & Backup
- Time Base Correctors
- Tower Kits
- Zorro Extenders & Busboards
- Mystery Corner
- Browse by Connection
- Sitemap
Tower Kits
Byte by Byte: PAL JR
Connection: Side Expansion Slot |
Front of Unit
Front of PAL JR
Back of PAL JR
Rear of Unit
Inside the unit
Inside the unit
Bottom of PAL JR
Side of the unit
Picture of staple connector
Picture of slots
Hi Res Version, Front of PAL JR - 226K
Hi Res Version of Front - 226K
Hi Res Version, Back of PAL JR - 295K
Hi Res Version of Back - 295K
Hi Res Version of Inside 1 - 341K
Hi Res Version of Inside 2 - 94K
Hi Res Version, Bottom of PAL JR - 341K
Image showing interior, without installed cards - 825K
Hi Res Version of Side - 25K
Image showing slots, with cards installed - 385K
Image showing staple board - 350K
Image showing staple board with cover removed - 421K
Dimensions: | Rougly the same size as an A1000 |
3.5" Bays: | 1 |
5.25" Bays: | None |
PSU: | Yes (unknown what spec) |
The PAL JR is an expansion box designed for use with the A1000. It sits directly on top of the A1000 and is connected by a small adaptor called "The Staple" which attaches to the A1000's side expansion slot. The unit appears to contain two Zorro II based slots for fitting cards. These slots appear to be electrically compatible with Zorro II, however due to the dimensions of the case, conventional full length Zorro II cards cannot be used, although half length cards can. In fact at least two custom Zorro II cards were built for use with this device and often supplied with it. These were the C2-ML, an ST506/MFM hard drive controller and the Garganturam RAM expansion. As these special Zorro II cards do not use conventional dimensions, they are unlikely to physically fit in any other Zorro II based system. The PAL JR has a drive bay for use with a hard drive, such as the one supplied with the C2-ML. The unit was supplied with one of three drives, a Seagate ST 225 (20.5MB), Seagate ST251 (40.7MB) or a Micro-Science 1050XX (42.5MB). Also according to the manual "The PAL Jr's ram has been placed in a memory space which recently was de-allocated from the reserved area of teh Amiga's memory map. This memory can be combined with optional memory cards to allow the Amiga to address a full 10 megabytes of user memory." The hard disk controller and RAM card were actually Commodore designs which are licensed to Byte-By-Byte for use.
Contributions to this page by:
Mark Ziegler
Letzte Änderung des Artikels: 2009-01-29 15:05
Revision: 1.0
You cannot comment on this entry