- Home
- Show all categories
- Models & Clones
- A1000 Accelerators
- A1200 Accelerators
- A2000 Accelerators
- A3000 Accelerators
- A4000 Accelerators
- A500 Accelerators
- A600 Accelerators
- Bridgeboards & Emulator Cards
- CD32 Accelerators
- CDTV Accelerators
- Custom Chips
- Digtizers & Framegrabbers
- Flickerfixer & Scandoubler
- Floppy Controller
- Genlocks
- Graphics (non RTG) & Video Cards
- Graphics Cards (RTG)
- I/O Karten
- IDE Controller
- ISDN & Modem
- Keyboards & Adapters
- Kickstart Switchers
- MIDI Devices
- Misc ZORRO Cards
- Misc. Hardware
- Monitors
- Network Cards
- Processors
- RAM Expansions
- Scanner
- SCSI Controller
- Sound Cards
- Soundsampler
- Tape Drives & Backup
- Time Base Correctors
- Tower Kits
- Zorro Extenders & Busboards
- Mystery Corner
- Browse by Connection
- Sitemap
Zorro Extenders & Busboards
Micronik: Z-2i
Connection: Trapdoor Slot (A1200) |
Rev 4.0, Front
Rev 4.0, Back
Rev 4.02, Front
Rev 4.02, Back
Rev 5.02, Front
Rev 5.02, Back
Hi Res Version, Rev 4.0 Front - 508K
Hi Res Version, Rev 4.0 Back - 369K
Hi Res Version, Rev 4.02 Front - 231K
Hi Res Version, Rev 4.02 Back - 243K
Hi Res Version, Rev 5.02 Front - 296K
Hi Res Version, Rev 5.02 Back - 342K
Image of the Video Slot Enabler - 146K
Image of adaptor - 220K
Keyboard Adaptor, connector closeup - 70K
Keyboard Adaptor, complete cable - 86K
Zorro II: | 5 | |
Zorro III: | None | |
ISA: | 3 or 4 x 16bit (3 inline) | (Non Active) |
PCI: | None | |
Video Slots: | None or 1 (inline) | (AGA Type) |
Other: | A1200 style trapdoor connector |
A busboard designed for A1200's towered with an appropriate tower kit such as the Micronik Infinitiv. Depending on the version of the board it may also have a combination of PCMCIA connector, 72pin SIMM slots, video slot and integrated keyboard adaptor. Not all versions of this busboard have those features. To use the Video Slot may require the use of the video slot enabler. It clips over the top of various chips on the A1200 motherboard, at the following locations, U30, U7, U8. In order to use an accelerator card with this busboard, the turbo jumper must be closed.
LOCATION | NUMBER OF PINS | LABELING |
Upper Left (REV 4.02 and REV5.02) |
2 Pins | GND * +12V |
Upper Left (REV4.02 only) |
4+1 Pins | Keyboard Cable Connector (Don't know for what cable.) |
Above the Power Connector |
REV4.02: 2+5 Pins REV5.02: 2+2 Pins |
unused * RESET1 - RESET1 * unused * unused * TURBO2 * TURBO2 RESET1 * RESET1 - TURBO2 * TURBO2 |
Power Connector (REV 4.02 and REV5.02) |
8 Pins | GND * GND * GND * +5V * +5V * -5V * +12V * -12V |
2) Close for use with an A1200 accelerator board.
Contributions to this page by:
Andreas Kähler, Christian, Martina Jacobs, Michael Grünseich, Pascal Rielland, Peter Olsson
Letzte Änderung des Artikels: 2009-01-29 16:09
Revision: 1.0
You cannot comment on this entry