A3000 Accelerators

ID #3048

ACT Elektronik Vertriebs GmbH: Apollo 4060

ACT Elektronik Vertriebs GmbH: Apollo 3060
Connection: CPU Fast Slot (A3000/A4000)

Processor:060@50Mhz or 060@66Mhz
FPU:Internal
MMU:Internal
Max Ram:128MB for 4040, 64MB for 3040
Ram Type:4 x 72pin SIMM slots for 4040, 2 x 72pin SIMM slots for 3040. (EDO works but is not taken advantage of)

The Apollo 4060 is designed to be plugged into the CPU Fast slot of the A4000 series machines as well as the A3000T. The Apollo 3060 is almost identical to the Apollo 4060 except it contains only two SIMM slots and is therefore better suited to fitting in a desktop A3000. The Apollo 3060 can still be used in A4000 series machines as well as the A3000T. Most versions of this card also contain a SCSI-II controller which is non-DMA but capable of transferring at up to 6MB/sec. The original 68040.library from Commodore cannot be used with this card, instead you must use the supplied library. Warning: The Apollo 3060 and 4060 contain a small PCB which is a voltage regulator, attached to some pins on the card. Never use the accelerator without this installed as you will kill the processor. The 060 is designed to run at 3.3V and without the voltage regulator it will receive 5V.

A4000/A4000T Installation

The motherboard jumpers marked CLK INT/EXT (or possibly CLK I/E) should be set to the INT (I) position, before installing the card. If the jumper is in the incorrect position, the machine will not boot.

A3000/A3000T Installation

For installation in an A3000 series machine, you must have at least Kickstart 2.04. You cannot use Kickstart V1.4, the pre-boot kickstart that loads the ROM from disk, regardless of the Kickstart version it eventually loads. NOTE: This card is reported not to work in versions of the A3000 shipped with an 030@16Mhz, although it may be possible to upgrade an oscillator on the motherboard to allow the card to work, this has not been confirmed.

CPUCLK (J104) Must be set to position INT on the motherboard
BRDCLK (J102) Must be set to position INT on the motherboard
QUADCLK (J100) Must be set to 25M on the motherboard.

For installation in an A3000 series machine you will require a chip adaptor which was usually supplied with the card. The SCSI chip on the motherboard and one of the Kickstart ROMs should be removed and inserted into the adaptor, wish is then placed into the empty sockets on the motherboard.

Jumpers

JUMPEROpenClosed
RAMRAM DisabledRAM Enabled
SCSIAutobooting disabledAutobooting enabled
060040 installed or 66Mhz 06050Mhz 060 installed
EDStandard DRAMs fittedEDRAMs fitted

Note: Most SIMMs do not contain EDRAMS which are DRAMs with an 8K cache, however if you use EDRAMs you can gain a speed increase by using this Jumper. EDRAM is NOT the same thing as EDO RAM.

Contributions to this page by:
Mario Misic, Stefan Nilsson, Tomas Gärdh

Tags: -

Related entries:

Last update: 2009-01-25 12:07
Revision: 1.0

Change language
 

Digg it! Print this record Send to a friend Show this as PDF file
Please use www.bboah.de for a translation proposal Please use www.bboah.de for a translation proposal
Please rate this entry:

Average rating: 0 out of 5 (0 Votes )

completely useless 1 2 3 4 5 most valuable

You can comment on this entry